Seametrics PT2X-BV Barometric and Vacum Sensor with Datalogging

The Seametrics PT2X-BV is a special version of the PT2X designed to measure barometric and vacuum pressure in reference to absolute pressure, along with temperature and time. It will measure pressure/vacuum from 600 to 1100 millibars.

seametrics pt2x bv barometrics and vacum sensor

Pressure measurement is accomplished utilizing an extremely rugged and stable 15 PSIA piezo-electric media-isolated pressure element combined with a 16-bit analog-to-digital converter.

This provides extremely accurate and stable pressure input into the microprocessor on the circuit board that measures the pressure, stores the data in non-volatile memory, and communicates the information via a serial communication link (RS485) to the host computer.

Temperature measurement is accomplished by utilizing a temperature sensor chip. The PT2X-BV is available in two enclosures – either an ABS weather-proof box or a stainless steel tube. The tube version is available with either a solid end cone or an NPT end cone for connecting to piping.

The PT2X-BV can be networked with other Seametrics Smart Sensors and controlled directly from a single computer. While most will use the PT2X-BV with our Aqua4Plus 2.0 software, it is by no means limited to that software. You can use your own Modbus® RTU or SDI-12 software or logging equipment to read measurements, thus tying into your existing telemetry and control systems.

Another Article:

Features

  • Measures & records barometric pressure/vacuum and temperature
  • Low power
  • Modbus® RTU (RS485) and SDI-12
  • ±0.05% FSO typical accuracy
  • Thermally compensated
  • Small diameter — 0.75” (1.9 cm)
  • 520,000 records in non-volatile memory
  • Barometric compensation utility for use with absolute sensors
  • Free, easy-to-use, newly upgraded Aqua4Plus 2.0 software

Applications

  • Barometrically compensate absolute
    sensors for level measurement
  • Measure vacuum pressure during
    vapor extraction pilot testing
  • Supplement aquifer test data in
    leaky or confined conditions

Specification

Box Enclosure Body Material ABS – IP66/67
Dimensions Box: 4.3” x 3.1” x 2.5” (10.9 x 7.9 x 6.4 cm)
Box and connectors: 4.3” x 3.6” x 2.5” (10.9 x 9.1 x 6.4 cm)
Wire Seal Material Fluoropolymer and Buna N
Tube & Cable Body Material Acetal & 316 stainless or titanium
Storage Range Without batteries: -40 ̊ to 80 ̊C (-40 ̊ to 176 ̊F)
Dimensions Cabled: 12.18” x 0.75” diameter (30.9 cm x 1.9 cm)
Cableless: 11.93” x 0.75” diameter (30.3 cm x 1.9 cm)
Wire Seal Material Fluoropolymer and PTFE
Weight 0.8 lb. (0.4 kg)
Cable Submersible: polyurethane, polyethylene, or ETFE (4 lb./100 ft., 1.8 kg/30 m)
Environmental IP68, NEMA 6P
Field Connector Standard
Temperature Operating Range Recommended: -15 ̊ to 55 ̊C (5 ̊ to 131 ̊F)
Storage Range Without batteries: -40 ̊ to 80 ̊C (-40 ̊ to 176 ̊F)
Power Internal Battery Two replaceable lithium ‘AA’ batteries – Battery life: 18 months at 15 min. polling interval (may vary do to environmental factors)
Auxiliary 12 Vdc – Nominal, 9-15 Vdc – range
Communication Modbus® RS485 Modbus® RTU, output=32bit IEEE floating point
SDI-12 SDI-12 (ver. 1.3) – ASCII
Logging Memory 4MB – 520,000 records
Logging Types Variable, user-defined, profiled
Logging Rates 8x/sec maximum, no minimum
Baud Rates 9600, 19200, 38400
Software Complimentary Aqua4Plus 2.0
Networking 32 available addresses per junction (Address range: 1 to 255)
File Formats .a4d and .csv
Output Channels Temperature Depth/Level
Element Digital IC onboard Silicon strain gauge transducer, 316 stainless or Hastelloy
Accuracy ±0.5°C — 0° to 55°C (32 ̊ to 131 ̊F)
±2.0°C — below 0°C (32 ̊F)
±0.05% FSO (typical, static)
±0.1% FSO (maximum, static)
(B.F.S.L. 20 ̊C)
Resolution 0.1 ̊C 0.0034% FS (typical)
Units Celsius, Fahrenheit, Kelvin PSI, FtH₂O, inH₂O, mmH₂O, mH₂O, inH₂O, cmHg, mmHg, Bars, Bars, kPa
Range -40 ̊ to 80 ̊C (-40 ̊ to 176 ̊F) 600 to 1100 millibars
Compensated 0 ̊ to 40 ̊C (32 ̊ to 104 ̊F)
Max operating pressure 1.1 x full scale
Burst pressure 2.0 x full scale

*Specifications subject to change. Please consult our web site for the most current data (seametrics.com). Modbus is a registered trademark of Schneider Electric.

For further information please contact : marketing@wmablog.com

Tinggalkan Balasan

Please log in using one of these methods to post your comment:

Logo WordPress.com

You are commenting using your WordPress.com account. Logout /  Ubah )

Foto Google

You are commenting using your Google account. Logout /  Ubah )

Gambar Twitter

You are commenting using your Twitter account. Logout /  Ubah )

Foto Facebook

You are commenting using your Facebook account. Logout /  Ubah )

Connecting to %s

This site uses Akismet to reduce spam. Learn how your comment data is processed.